Manley Massive Passive Stereo Tube EQ
Loosely based upon the Pultec EQP1-A, the Manley Massive Passive tube equaliser falls well short of the Pultec’s magic but is nevertheless an excellent dual/two channel tube eq. It adds sparkle and fullness to signals and mixes and of course, it looks great racked next to your Manley Vari Mu. A pretty decent unit. ~ Eccentric
The Manley Massive Passive is a 2 channel, 4 band passive tube equaliser that adds clarity and a very musical feel to sound sources even when used at high levels.
Using all passive components along with metal film resistors, film capacitors and hand wound inductors, the Massive Passive creates an organic natural tone when mixing.
The EQ comes with four low-pass filters and five high-pass filters which can be both bypassed to A/B your results. This makes it easy to remove unwanted frequencies that are muddying your mix. The filters are extra steep up to 36dB/octave to ensure total cut off is achieved.
The Massive Passive features easy to use controls that enable you to perform precise equalisation tasks quickly and accurately, or use it to get creative to shape your sound into something new without colourising the original source.
Manley’s Massive Passive can also be used as a mastering tool, however there is a master-specific stepped EQ Mastering Version also available for more specific tasks.
Features:
- All-Passive tone sculpting circuitry
- Unique Shelf curves use the “bandwidth” control
- Overlapping and Interleaved Frequency choices
- Every band is switchable to shelf or bell
- Vacuum tube make-up gain and line drivers
- Parallel symmetrical topology
- Premium components used throughout
- Hi pass and Low pass Filters and gain trims
In Depth Features:
- Each of the 4 bands of EQ can be bypassed or set to boost or cut providing twice as much control over conventional EQs while also eliminating the problem of a center detent not guaranteeing flat response.
- Astounding headroom and freedom from clipping can be achieved with 20 dB of boost or cut on each EQ band.
- Maximum effectiveness is gained from the steep High pass and Low pass filters and minimal coloration can be achieved passively. The minimum slope is 18 dB/octave and the 18kHz filter was designed for 60 dB/octave.
- The transformer balanced outputs give a desirable touch of flavour and were designed to accommodate the maximum boosts possible.
Specifications
- High Pass Filters = 22, 39, 68, 120, 220, OFF
- Low Pass Filters = 6K, 7K5, 9K, 12K, 18K, OFF
- Parametric Frequencies:
- LOW – 22, 33, 47, 68, 100, 150, 220, 330, 470, 680, 1K
- LM – 82, 120, 180, 270, 390, 560, 820, 1K2, 1K8, 2K7, 3K9
- HM – 220, 330, 470, 680, 1K, 1K5, 2K2, 3K3, 4K7, 6K8, 10K
- HI – 560, 820, 1K2, 1K8, 2K7, 3K9, 5K6, 8K2, 12K, 18K, 27K
- Ins & Outs Balanced XLR & 1/4″ (accepts unbalanced)
- Level +4 dBu nominal, internal switches for -10 operation
- Bypass Switch bypasses EQ & tube circuits (not hardwire)
- 44 Frequencies (roughly 1/4 octave spacing)
- Frequency Range: 22 Hz to 27 Khz
- EQ Boost/Cut Range : 20 dB boost, 20 dB cut
- Nominal Q range: 1.5 to 3 (uniquely active in shelf modes)
- Frequency Response: +/- 2 dB: 8 Hz to 60 KHz
- Maximum Output @ 1.5% THD +37 dBv; +26dBv @ 20 Hz
- THD & Noise (1KHz @ +4 dBu): 0.06%
- Noise Floor (referred to +4dBu): -85 dB (A Weight)
- Dynamic Range: 120 dB
- Tube Complement: 2 x 12AX7 EH, 4 x 6414 for serial MSMPX### after 2/2004
- Tube Complement: 2 x 5751, 4 x 6414 for serial MSMP### until 2/2004
- Power Consumption (120/240VAC): 72 watts
- Unit is factory set for 100V, 120V or 220-240VAC operation for original destination country’s mains voltage.
- Operating Mains Voltage changeable with power transformer changeover switch and fuse value change.
- Mains Voltage Frequency: 50~ 60Hz
- Size (3U): 19″ x 5.25″ x 10″
- Weight: Unit 21 lbs. Shipping Weight: 27 lbs.