The Manley Core Channel Strip is a unique tool for your studio. Building upon its 25-year legacy producing revered recording studio equipment, Manley Labs has distilled its CORE technologies from this lineage. 2014 delivers the Manley CORE, an innovative channel strip that combines Manley’s Greatest Hits with fresh technology. The remarkably intuitive front panel combines musical and forgiving circuitry that allows the musician to concentrate on her/his performance instead of being lost in a sea of knobs. Ease of use and intelligently chosen operating points make it virtually impossible to cut a bad sounding track!
MANLEY CORE FRONT PANEL CONTROLS:
- 48V Phantom power switch
- 120Hz High Pass Filter switch
- Phase Invert switch
- Input Attenuator (Variable Pad)
- Mic Pre Selectable Gain 40dB or 60dB
- Line Amp Selectable Gain 20dB or 40dB
Manley CORE Reference Channel Strip Tech Spec
- ALL-TUBE preamplifier audio path using 1 x 12AX7 for gain and 1 x 6922 White Follower
- Balanced Transformer Coupled XLR Microphone Input Impedance: 1200 Ohms
- Balanced XLR Line Input Impedance: 10 kOhms
- Unbalanced 1/4″” Direct Input Impedance: 10 Meg Ohm
- Hi-current drive Direct XLR output Impedance: 50 Ohms
- Silent conductive plastic INPUT attenuator
- Microphone preamp high pass filter starting at 120Hz with a 6dB/8va slope
- Compressor Maximum GAIN REDUCTION: 16 dB
- Compressor ATTACK time: 60ms slowest CCW, 30ms at 12:00, 5ms fastest CW for 6dB compression
- Compressor RELEASE time: 1.5s slowest CCW, 1s at 12:00, 100ms fastest CW from 6dB compression
- Maximum Input Mic input (Low Gain Setting): -5 dBu or 435mV RMS @ 0.5% THD
- Maximum Input Mic input (High Gain Setting): -25 dBu or 44 mV RMS @ 0.5% THD
- Maximum Input Line input (Low Gain Setting): +13 dBu or 3.5V RMS @ 0.5% THD
- Maximum Input Line input (High Gain Setting): -8 dBu or 300mV RMS @ 0.5% THD
- Maximum Input Direct input (Low Gain Setting): +24 dBu or 12V RMS @ 0.5% THD
- Maximum Input Direct input (High Gain Setting): +17 dBu or 5.5V RMS @ 0.5% THD
- Maximum Input Insert return: +20 dBu or 7.8V RMS @ 0.5% THD
- Maximum Preamp Output (Insert Send): +35 dBu or 43V RMS @ 0.5% THD
- Maximum Preamp Output (Insert Send): +22 dBu into 600 Ohms
- Maximum Main Output: +20 dBu
- Insert Send output impedance: 50 Ohms
- Insert Return input impedance: 13 kOhms
- Main Output Impedance: 50 Ohms
- Direct Output Headroom (referenced to +4 dBv): 31 dB
- Main Output Headroom (referenced to +4 dBv): 16 dB
- Dynamic Range: >90 dB
- Frequency Response: 10 Hz to 20 kHz ±0.5 dB
- Large LED illuminated VU METER
- Meters switch to read Direct Output (1) from preamp, Output (2) from Main Out, or Compressor Gain Reduction
- THD & Noise (1kHz @ +4 dBm): 0.02% at Low Gain setting
- Noise Floor (Gain set to minimum): -70 dB wideband typical
- Gain via Microphone Input: 40 or 60 dB
- Gain via Line Input: 20 or 40dB
- Maximum Gain of EQ & Limiter section: 10 dB
- AUTOMUTE warmup delay: 30 Seconds
- Power consumption: 35 watts
- Operating mains voltage: 90 to 254 VAC (internal universal supply)
- Mains Voltage Frequency: 50-60Hz
- Dimensions: 19″” x 3 1/2″” x 7″” (occupies 2u)
- Unit Weight: 8.3 lbs.
- Shipping weight: 11.5 lbs.