BAE 1073 MPF Single Channel Mic Pre w/power supply
This is basically a deluxe 1073MP. lt has all the same qualities as the 1073MP with one added feature, a high pass filter. We integrated the same inductor based high pass filter that’s in the 1073 and added it here to the 1073MPFSame transformers as the 1073, same hand-wired modular construction that BAE is known for.
1. Phase reverse button.
2. Impedance select between 1200 and 300 ohms.
3. Direct input switch.
4. Balanced line input
5. 48v phantom power. Same 283 amp card as 1073 Same 182 filter card as 1073 Same transformers as the 1073 Same hand-wired modular construction that BAE is known for.
Features
- 1. Phase reverse button.
- 2. Impedance select between 1200 and 300 ohms.
- 3. Direct input switch.
- 4. Balanced line input
- 5. 48v phantom power.
- Same 283 amp card as 1073
- Same transformers as the 1073
- Same hand-wired modular construction that BAE is known for.
- Two Class A preamps with direct inputs in a single rack space with a power supply
- High Impedance direct input for guitar and synthesizer
- Output level control serves as gain trim between the 5 dB steps on gain switch
- Balanced mic input and balanced +4 dB output are on XLR connectors on the rear of the module.
- Similar Class A preamp as Neve™* 1073 equalizer/preamp modules
- Pad is an integral part of the gain switch same as Neve™* 1073 equalizer/preamp modules
- Oversize remote power supply can operate up to four channels of preamp
- One-year warranty
- 10 Day satisfaction guarantee
The 1073MPF preamp yields a really fat sound. It seems to add subharmonics to the low end which makes the bottom end sound huge. It smoothes the top end which gives the highs a silky sheen. As well the 1073MPF compresses transients a little bit. It is a smooth, fat., larger than life sound. An added bonus is to use the DI inputs to fatten samples, synths and mixes since the DI can handle line levels. Set the gain knob (red Marconi) around 20 on the dial and set the output (grey knob) fully clockwise. This gives you the highest headroom and cleanest signal path. Every click is in 5db increments so if one click is too hot, attenuate the output to get in between the 5db steps.Another trick people like to do is to put the final mix through the balanced line inputs on the back to get that harmonic distortion. To get even more of that Class A output stage is to come out of channel 1 and into channel 2 then you have an accumulative effect of that classic output stage.
* Neve is a trademark or registered trademark of AMS-Neve LTD and BAE is not affiliated with such entity.
Includes BAE 24V PSU to operate.
The power supply can run 2 units simultaneously thats why units are sold separately.
Specifications
Frequency Response
- 10Hz to -3dB at 55kHz
Mic Input Impedance
- ≈1200/300 ohms
Line Input Impedance
- 10k ohms
DI Input Impedance
- ≈150k ohms
Output Impedance
- 65 ohms
Common Mode Rejection Ratio
- 100dB min @ 60Hz
Maximum Output Level
- +27.4 dBu @ 600Ω
Power Requirements
- 115/230 VAC, 30W
Gain dB
- 0 to 71 dB
Equivalent Input Noise
- -110 dBu; Unweighted 300kHz Bandwidth
Weight (Single/Dual)
- 8 LBS/3.63 KG
- 10 LBS/4.54 KG
Dimensions (Inches)
- 19W x 1.75L x 9D