DPA Microphones 5006-11A d:mension™ Surround Kit
- Five carefully matched microphones
- Useful as orchestral main pair
- Peli™ Case transportation and protection
Even though the standard tolerances onour pencil mics are extremely low, the surround match is even closer. The specially-selected 4006As are matched within ±0.5 dB on both frequency response and sensitivity. The 4011As are matched within ±1 dB.
The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the 4006A Omnidirectional Microphones the perfect choice for all AB Stereo, Decca Tree or surround main array recordings.
The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone / accessory inlays.
DPA Microphones 4006A Specifications
Directional characteristics:
Omnidirectional
Principle of operation:
Pressure
Cartridge type:
Pre-polarized condenser
Frequency range:
10 Hz to 20 kHz
Frequency range, ± 2 dB:
10 Hz to 20 kHz
Sensitivity, nominal, ±2 dB at 250 Hz:
40 mV/Pa; -28 dB re. 1 V/Pa
Equivalent noise level, A-weighted:
Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A))
Equivalent noise level, ITU-R BS.468-4:
Typ. 27 dB (max. 29 dB)
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL):
Typ. 79 dB(A)
Total Harmonic Distortion (THD):
< 1 % up to 139 dB SPL peak
Minimum load impedance:
2 kohm
Dynamic range:
Typ. 124 dB
Max. SPL, peak before clipping:
147 dB
Switchable attenuator:
0 dB / -20 dB
Output impedance:
< 200 ohm
Cable drive capability:
100 m (328 ft)
Output balance principle:
Impedance balancing with Active Drive
Common Mode Rejection Ratio (CMRR):
> 60 dB
Power supply (for full specifications):
48 V Phantom power (± 4 V)
Current consumption:
2.8 mA
Connector:
XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: – phase
Color:
Matte black
Weight:
163 g (5.7 oz)
Diameter:
16 to 19 mm (0.63 to 0.75 in)
Capsule diameter:
16 mm (0.63 in)
Length:
170 mm (6.7 in)
Output voltage, RMS:
> 5 V
Polarity:
+V at Pin 2 for positive sound pressure
Temperature range:
-40 °C to 50 °C (-40 °F to 122 °F)
Relative Humidity (RH):
Up to 90 %
Classification:
Conforms to IEC 61672 Class I (with Near-field Grid DD0251)
Matching tolerance:
± 0.5 dB
Phase deviation for kit:
< 5°
DPA Microphones 4011A Specifications
Directional characteristics:
Cardioid
Principle of operation:
Pressure gradient
Cartridge type:
19 mm (0.75 in) pre-polarised condenser
Frequency range, ± 2 dB:
40 Hz – 20 kHz
Sensitivity, nominal, ±2 dB:
10 mV/Pa; -40 dB re. 1 V/Pa
Equivalent noise level A-weighted:
Typ. 19 dB(A) re. 20 µPa (max. 20 dB(A))
Equiv. noise level ITU-R BS.468-4:
Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting)
S/N ratio, re. 1 kHz at 1 Pa (94 dB SPL):
75 dB(A)
Total harmonic distortion (THD):
< 0.5% up to 110 dB SPL peak,
Dynamic range:
Typ. 97 dB
Max. SPL, peak before clipping:
158 dB
Attenuators, filters etc.:
0 dB, -20 dB
Output impedance:
< 200 ohm
Cable drive capability:
Up to 100 m (328 ft)
Power supply:
48 V Phantom power
Current consumption:
2.60 mA
Connector:
3-pin XLR-M (Standard P48)
Weight:
165 g (5.82 oz)
Capsule diameter:
19 mm (0.75)
Length:
175 mm (6.89 in)
Operating temperature range:
-40 to +55°C (-40 to 131°F)